Re: Unsubscribe

I got one of these last Christmas. It works great, but the device has no
obvious power source and now I can't find my cat.

God help me when I accidently try to unsubscribe like that ..
Carlo


<felix@crowfix.com> wrote in message
news:20061003172911.GA4069@crowfix.com...
> On Mon, Oct 02, 2006 at 01:36:17PM -0400, uwcssa wrote:
>>  Please unsubscribe me!  Thank you!
>>
>>
>> Also, it would be better to have a message foot saying how to
>> unsubscribe.
>
> Will this do?  It's too big for a footer.
>
> Here's how to unsubscribe:
>
> First, ask your Internet Provider to mail you an Unsubscribing Kit.
> Then follow these directions.
>
> The kit will most likely be the standard no-fault type. Depending on
> requirements, System A and/or System B can be used. When operating
> System A, depress lever and a plastic dalkron unsubscriber will be
> dispensed through the slot immediately underneath. When you have
> fastened the adhesive lip, attach connection marked by the large "X"
> outlet hose. Twist the silver-coloured ring one inch below the
> connection point until you feel it lock.
>
> The kit is now ready for use. The Cin-Eliminator is activated by the
> small switch on the lip.  When securing, twist the ring back to its
> initial condition, so that the two orange lines meet.  Disconnect.
> Place the dalkron unsubscriber in the vacuum receptacle to the rear.
> Activate by pressing the blue button.
>
> The controls for System B are located on the opposite side. The red
> release switch places the Cin-Eliminator into position; it can be
> adjusted manually up or down by pressing the blue manual release
> button. The opening is self-adjusting. To secure after use, press the
> green button, which simultaneously activates the evaporator and
> returns the Cin-Eliminator to its storage position.
>
> You may log off if the green exit light is on over the evaporator.  If
> the red light is illuminated, one of the Cin-Eliminator requirements
> has not been properly implemented. Press the "List Guy" call button on
> the right of the evaporator. He will secure all facilities from his
> control panel.
>
> To use the Auto-Unsub, first undress and place all your clothes in the
> clothes rack. Put on the velcro slippers located in the cabinet
> immediately below. Enter the shower, taking the entire kit with
> you. On the control panel to your upper right upon entering you will
> see a "Shower seal" button. Press to activate. A green light will then
> be illuminated immediately below. On the intensity knob, select the
> desired setting. Now depress the Auto-Unsub activation lever. Bathe
> normally.
>
> The Auto-Unsub will automatically go off after three minutes unless
> you activate the "Manual off" override switch by flipping it up. When
> you are ready to leave, press the blue "Shower seal" release
> button. The door will open and you may leave. Please remove the velcro
> slippers and place them in their container.
>
> If you prefer the ultrasonic log-off mode, press the indicated blue
> button. When the twin panels open, pull forward by rings A & B. The
> knob to the left, just below the blue light, has three settings, low,
> medium or high. For normal use, the medium setting is suggested.
>
> After these settings have been made, you can activate the device by
> switching to the "ON" position the clearly marked red switch. If
> during the unsubscribing operation you wish to change the settings,
> place the "manual off" override switch in the "OFF" position. You may
> now make the change and repeat the cycle. When the green exit light
> goes on, you may log off and have lunch. Please close the door behind
> you.
>
>
> --
>            ... _._. ._ ._. . _._. ._. ___ .__ ._. . .__. ._ .. ._.
>     Felix Finch: scarecrow repairman & rocket surgeon / felix@crowfix.com
>  GPG = E987 4493 C860 246C 3B1E  6477 7838 76E9 182E 8151 ITAR license
> #4933
> I've found a solution to Fermat's Last Theorem but I see I've run out of
> room o
>
> ---------------------------(end of broadcast)---------------------------
> TIP 9: In versions below 8.0, the planner will ignore your desire to
>       choose an index scan if your joining column's datatypes do not
>       match
>