Обсуждение: Re: [BUG] Autovacuum not dynamically decreasing cost_limit and cost_delay
Moving to bugs list.
On Tue, Oct 26, 2021 at 11:23 AM Scott Mead <scott@meads.us> wrote:
On Wed, May 26, 2021 at 4:01 AM Masahiko Sawada <sawada.mshk@gmail.com> wrote:On Wed, Apr 14, 2021 at 11:17 PM Mead, Scott <meads@amazon.com> wrote:
>
>
>
> > On Mar 1, 2021, at 8:43 PM, Masahiko Sawada <sawada.mshk@gmail.com> wrote:
> >
> > CAUTION: This email originated from outside of the organization. Do not click links or open attachments unless you can confirm the sender and know the content is safe.
> >
> >
> >
> > On Mon, Feb 8, 2021 at 11:49 PM Mead, Scott <meads@amazon.com> wrote:
> >>
> >> Hello,
> >> I recently looked at what it would take to make a running autovacuum pick-up a change to either cost_delay or cost_limit. Users frequently will have a conservative value set, and then wish to change it when autovacuum initiates a freeze on a relation. Most users end up finding out they are in ‘to prevent wraparound’ after it has happened, this means that if they want the vacuum to take advantage of more I/O, they need to stop and then restart the currently running vacuum (after reloading the GUCs).
> >>
> >> Initially, my goal was to determine feasibility for making this dynamic. I added debug code to vacuum.c:vacuum_delay_point(void) and found that changes to cost_delay and cost_limit are already processed by a running vacuum. There was a bug preventing the cost_delay or cost_limit from being configured to allow higher throughput however.
> >>
> >> I believe this is a bug because currently, autovacuum will dynamically detect and increase the cost_limit or cost_delay, but it can never decrease those values beyond their setting when the vacuum began. The current behavior is for vacuum to limit the maximum throughput of currently running vacuum processes to the cost_limit that was set when the vacuum process began.
> >
> > Thanks for your report.
> >
> > I've not looked at the patch yet but I agree that the calculation for
> > autovacuum cost delay seems not to work fine if vacuum-delay-related
> > parameters (e.g., autovacuum_vacuum_cost_delay etc) are changed during
> > vacuuming a table to speed up running autovacuums. Here is my
> > analysis:
>
>
> I appreciate your in-depth analysis and will comment in-line. That said, I still think it’s important that the attached path is applied. As it is today, a simple few lines of code prevent users from being able to increase the throughput on vacuums that are running without having to cancel them first.
>
> The patch that I’ve provided allows users to decrease their vacuum_cost_delay and get an immediate boost in performance to their running vacuum jobs.
>
>
> >
> > Suppose we have the following parameters and 3 autovacuum workers are
> > running on different tables:
> >
> > autovacuum_vacuum_cost_delay = 100
> > autovacuum_vacuum_cost_limit = 100
> >
> > Vacuum cost-based delay parameters for each workers are follows:
> >
> > worker->wi_cost_limit_base = 100
> > worker->wi_cost_limit = 66
> > worker->wi_cost_delay = 100
Sorry, worker->wi_cost_limit should be 33.
> >
> > Each running autovacuum has "wi_cost_limit = 66" because the total
> > limit (100) is equally rationed. And another point is that the total
> > wi_cost_limit (198 = 66*3) is less than autovacuum_vacuum_cost_limit,
> > 100. Which are fine.
So the total wi_cost_limit, 99, is less than autovacuum_vacuum_cost_limit, 100.
> >
> > Here let's change autovacuum_vacuum_cost_delay/limit value to speed up
> > running autovacuums.
> >
> > Case 1 : increasing autovacuum_vacuum_cost_limit to 1000.
> >
> > After reloading the configuration file, vacuum cost-based delay
> > parameters for each worker become as follows:
> >
> > worker->wi_cost_limit_base = 100
> > worker->wi_cost_limit = 100
> > worker->wi_cost_delay = 100
> >
> > If we rationed autovacuum_vacuum_cost_limit, 1000, to 3 workers, it
> > would be 333. But since we cap it by wi_cost_limit_base, the
> > wi_cost_limit is 100. I think this is what Mead reported here.
>
>
> Yes, this is exactly correct. The cost_limit is capped at the cost_limit that was set during the start of a running vacuum. My patch changes this cap to be the max allowed cost_limit (10,000).
The comment of worker's limit calculation says:
/*
* We put a lower bound of 1 on the cost_limit, to avoid division-
* by-zero in the vacuum code. Also, in case of roundoff trouble
* in these calculations, let's be sure we don't ever set
* cost_limit to more than the base value.
*/
worker->wi_cost_limit = Max(Min(limit,
worker->wi_cost_limit_base),
1);
If we use the max cost_limit as the upper bound here, the worker's
limit could unnecessarily be higher than the base value in case of
roundoff trouble? I think that the problem here is rather that we
don't update wi_cost_limit_base and wi_cost_delay when rebalancing the
cost.Currently, vacuum always limits you to the cost_limit_base from the time that your vacuum started. I'm not sure why, I don't believe it's rounding related because the rest of the rebalancing code works properly. ISTM that looking simply allowing the updated cost_limit is a simple solution since the rebalance code will automatically take it into account.
Regards,
--
Masahiko Sawada
EDB: https://www.enterprisedb.com/
--
--
This is a bug/design which is causing real pain in operations.
There are cases the autovacuum worker runs for days and we are left with no option other than cancelling it.